Skateboard Wheel Calculator: size and hardness
Work out the skateboard wheel diameter (mm) and hardness (A scale) that suit you based on your style, the ground you skate on and whether you prefer control or speed.
Your wheel setup
Wheels are the component that changes the feel of skating the most and, paradoxically, where most people improvise. You buy some because you like the graphics or because they were what the shop had, and then you don’t understand why you skate weird. The reality is that each combination of diameter + hardness + type is designed for something specific.
This calculator recommends the exact mm range and A durometer based on your style, the surface you usually skate and whether you prioritize speed or control.
What each value measures
Diameter (mm)
This is the size of the wheel. Common sizes:
- 48-52 mm: old-school street, ultra-fast flips. Very niche.
- 52-54 mm: the sweet spot of modern technical street.
- 55-58 mm: park and smooth transitions. More sustained speed.
- 58-62 mm: bowl, vert, fast cruising.
- 62-75 mm: pure cruising, longboard, surfskate.
More diameter = more speed and better grip on rough ground. Less diameter = less weight and easier flips.
Durometer (A scale)
It measures the hardness of the urethane. The scale goes from 70A (rubbery) to 101A (very hard). In skating:
- 78-87A: soft wheels. For cruising on rough asphalt. They absorb.
- 88-95A: medium. Park and transitions, where you want some grip.
- 95-99A: hard. Park / bowl / street on good surface.
- 99-101A: very hard. Technical street, clean slides, they don’t flat-spot.
Some brands use the B scale (Bones SPF) which starts where the A scale ends. 84B ≈ 104A.
Type / Formula
Not all hard wheels are the same. Brands like Bones have specific formulas:
- STF (Street Tech Formula): very hard, no flat spots, controlled slide.
- SPF (Skatepark Formula): hard but with more rebound, better for polished concrete parks.
- ATF (All Terrain Formula): soft, big, for any asphalt.
Spitfire has Formula Four (its premium line), Ricta has Clouds (street with rebound), Powell has Snakes (soft bowl wheels)…
How the surface affects it
The surface you usually skate changes more things than you think:
| Surface | Recommended setup |
|---|---|
| Polished concrete skatepark | Wheels 52-54mm 99-101A. You make the most of the ground speed, clean slides. |
| Indoor / wooden skatepark | 53-55mm 95-99A. Slightly softer so they don’t bounce. |
| Street with regular asphalt | 54-56mm 95-99A. A bit bigger for vibrations. |
| Street with very bad asphalt | 56-60mm 87-95A. Softer and bigger wheels so the trip to the spot doesn’t punish you. |
How skater weight affects it
The catalog doesn’t tell you, but it’s real: if you weigh a lot (85+ kg), soft wheels flat-spot faster and perform worse. The quick rule:
- < 60 kg: any standard hardness is fine.
- 60-80 kg: standard hardness for your style.
- 80-95 kg: go up 1-2 durometer points from “standard”.
- > 95 kg: maximum hardness (101A in street, 99A in park).
Core: does it matter?
Yes, but less than it seems for normal use. Premium wheels have a hard plastic center core where the bearing sits. Without a core (or with a cheap one), the bearing moves and the wheel wears out sooner.
For an amateur skater who trains 2-3 times a week, any wheel from a known brand has a decent core. For pros filming lines for hours, premium cores (Bones STF, Spitfire F4) make a real difference.
Common mistakes
- Buying 99A for urban cruising. No. If you’re going down the street for bread, soft wheels (78-85A). Hard ones will rattle you over every paving stone.
- Buying 78A for street. Impossible to slide. Impossible to flip precisely. Soft wheels shift the setup on every turn.
- Mixing diameters between the front and rear truck. Some skaters do it on purpose (bigger at the back for pushing speed), but unless you know what you’re doing, keep all 4 the same.
- Not rotating the wheels every 1-2 months. If you always skate with the same foot forward (you’re goofy or regular), two wheels wear more. Swapping their position evens them out and they last twice as long.
How long wheels last
It depends a lot on the style:
- Technical street with lots of slides: 4-8 months for a premium set.
- Park / bowl: 1-2 years. They barely wear.
- Urban cruising: 2-3 years. They only get “smoothed” but don’t break.
- Longboard / freeride with slides: 3-6 months. That’s what slides do.
You know it’s time to change them when: the diameter has dropped >5 mm, there are visible flat spots, or “coning” appears (the wheel becomes conical).
Frequently asked questions
Are more expensive wheels better?
Generally yes, especially for durability. A Bones STF costs twice as much as a generic wheel but lasts three times longer. In cost per month, the good ones come out cheaper.
Bones, Spitfire or Ricta?
All three are references. The real difference:
- Bones STF: the longest lasting. Very controlled slide.
- Spitfire F4: slightly better rebound, more sense of speed.
- Ricta Clouds: a middle ground, good price, more original graphics.
How much does a decent set of wheels cost?
30-45€ for premium (Bones, Spitfire, Ricta), 18-25€ for entry-level but good (OJ, Powell, Element), 10-15€ for cheap ones that last half as long.
Can soft wheels be used in the park?
You can, but you won’t perform. You skate very slowly, slides feel odd and they flat-spot in one session. If you only have one board and skate park + street to the spot, look for a middle point: 56mm 92A.
Can I use longboard wheels on my skateboard?
Physically yes (with a tall riser), but it loses its point. The board feels twice as heavy, flips don’t come out and the control is that of a cruiser. For that, better to have a dedicated cruiser.
Keep going
- How to choose skateboard wheels: complete guide with types, brands and when to change.
- How to choose skateboard trucks: the other component that goes with the wheels.
- Skateboard size calculator: the setup starts with the deck.
- Skateboard truck size calculator: exact width by brand.