If you skate, chances are you’re running something from Bones: STF wheels, Reds bearings, or both. Bones is really two sister brands, Bones Wheels and Bones Bearings, which came from the same person: George Powell, the engineer who founded Powell Peralta. Its wheels were the first white wheels in skateboarding, and its bearings broke with the ABEC scale everybody else used.
In this profile you get the history of Bones, who owns it, where its wheels and bearings are made, what STF, SPF and Skate Rated mean, how to choose, how to clean bearings and how to avoid fakes.
How Bones wheels started
In the mid 70s, George Powell was an engineer who had studied at Stanford and worked in aerospace. His son asked him for a board, and Powell realized how much wheels had changed: the old clay ones stopped dead on any pebble, and the new urethane ones gripped and rolled in a different way. He started testing at home.
He developed his own urethane in the kitchen, with a mix of two commercial compounds. The result was an opaque white wheel, when all the others were semi-transparent. Because of that bone color he called them Bones. The first batches were hard: Powell has said the wheels were tough to pour and plenty of them didn’t come out right.
In November 1976 he founded Powell Corporation in Santa Barbara, which sold a slalom board for Tom Sims and the Bones wheels. In 1978 he partnered with Stacy Peralta, the company became Powell Peralta and in 1979 the Bones Brigade was born, the team of Tony Hawk, Rodney Mullen and Steve Caballero. You have all that history in the Powell Peralta profile. Even though they share a name, there’s no official explanation that the Bones Brigade is named after the wheels.
How Bones bearings started
In the early 80s skateboarding was in a slump and good bearings were hard to find. Powell says that American manufacturers had left the market, that the Japanese ones were good but not fast, and that the German ones were faster but not fast enough. He searched across the United States and Europe until he found a small Swiss manufacturer that made custom bearings, faster than all the ones they had tried and only a little more expensive than the German ones.
With that manufacturer they changed several things about the traditional bearing:
- A molded, removable plastic retainer, instead of a metal one.
- A single shield, on one side, so you can clean and lube without tools.
- Tolerances and clearances designed for the side loads and impacts of skateboarding.
- A lubricant of their own, Speed Cream.
That’s how the Bones Swiss were born, in development since 1981. In the 90s Powell put out a cheaper version made in China, after two years of testing: the Bones Reds, which you see today in almost any skateboard.
Who owns Bones?
Bones Wheels and Bones Bearings belong to Skate One Corp., based in Goleta, next to Santa Barbara. It’s the company George Powell founded in 1976: when Stacy Peralta left at the end of 1991 it went back to being called Powell Corporation, and over the years it became Skate One. It has never been sold to any outside group, and Powell still signs the brand’s technical texts.
Skate One also owns Powell Peralta, Mini Logo and other smaller brands of decks, trucks and roller skates. The company boasts that in all these years it hasn’t stopped manufacturing for a single day, and that Bones wheels and bearings are what sells the most.
Where they’re made
| Product | Where it’s made |
|---|---|
| Bones wheels (all formulas) | California, at Skate One’s own plant |
| Bones Swiss bearings | Switzerland, by a small custom manufacturer |
| Reds, Super Reds and Big Balls bearings | China, to Bones’ specifications |
The fact that Reds are made in China doesn’t mean they’re fake: George Powell explains it openly in the brand’s official history, and criticizes the brands that hide it. What is a sign of a fake is a box of Bones Swiss that says “Made in China”.
Bones wheels: STF, SPF, X-Formula and ATF
Bones organizes its wheels by formulas, each built for a terrain, and within each formula by shapes.
| Formula | What for | Hardness |
|---|---|---|
| STF (Street Tech Formula) | Street and technical street | 99A and 103A |
| SPF (SkatePark Formula) | Skatepark, bowl and transition | 81B and 84B (about 101A and 104A) |
| X-Formula | Rough ground and long sessions | X95, X97 and X99 |
| ATF (All Terrain Formula) | Cruiser, filming, bad asphalt, cobblestone | 80A |
| OG 100 (Original Formula) | All-terrain, good for starting out | 100A |
The SPFs use the B scale, which reads 20 points lower than the A scale: an 84B is roughly a 104A. They’re very hard and fast in a smooth skatepark, but on the street they can feel rough. The X-Formulas are softer than the STFs and absorb vibration better, without losing much speed.
The shapes: V1 to V6
The “V” doesn’t mean the version of the formula, but the wheel’s profile:
| Shape | What it’s like |
|---|---|
| V1 Standard | The neutral one, for everything |
| V2 Locks | A profile that helps lock onto rails and curbs |
| V3 Slim | Narrow and light |
| V4 Wide | Wider, more contact with the ground and more stability |
| V5 Sidecut | With a side cut that reduces drag on slides and grinds |
| V6 Wide-Cut | The width of the V4 with the cut of the V5 |
The SPFs have their own shapes, like the P5 Sidecut and the P6 Wide-Cut, and the ATFs come in two versions: the Rough Riders and the Filmer, for people who film.
If you want more detail to choose, we have a guide to choosing skateboard wheels and a comparison of the best skateboard wheels.
Bones bearings: Reds, Super Reds and Swiss
All Bones bearings are 608, the standard skateboard size, with an 8 mm axle. Reds and Swiss have a single removable shield and come lubed with Speed Cream.
| Model | Where it’s made | What it’s like |
|---|---|---|
| Reds | China | Copies the Swiss design at less than half the price. Red shield, seven balls |
| Super Reds | China | Better quality steel races, more precise balls, better finish. Quieter and longer lasting |
| Big Balls Reds | China | Six larger balls. Faster and more resistant to dirt, a bit noisier |
| Reds Ceramics | China | With ceramic balls |
| Swiss | Switzerland | The original: the fastest and the most used in competition |
| Swiss 6 | Switzerland | With six balls instead of seven |
| Swiss Labyrinth | Switzerland | With two non-contact shields, so less dirt gets in |
| Swiss Ceramics | Switzerland | Ceramic balls: lighter, harder and they don’t rust |
If you’re torn between steel and ceramic, we have an article on steel vs ceramic bearings, and a model-by-model guide to Bones bearings.
Why Bones doesn’t use the ABEC scale
It’s one of the most searched questions about Bones: “what ABEC are Reds?”. The answer is none, and George Powell himself has explained why.
ABEC stands for the Annular Bearing Engineers Committee, a committee that sets the tolerances, geometry and noise of industrial bearings, in grades 1, 3, 5, 7 and 9. It only has odd numbers because the committee wanted five levels and picked the odd ones. But the scale doesn’t measure anything that matters on a skateboard: not impacts, not side loads, not materials, not the lubricant, not the retainer.
On top of that, the high ABEC grades are built for speeds a skateboard never reaches. A 54 mm wheel at 20,000 revolutions per minute would be going about 125 mph. A skateboard rarely goes past about 30 mph, around 4,700 revolutions, and most of the time it’s under 2,000. That’s why Bones designed its bearings from scratch and created its own standard, Skate Rated.
Skate Rated is the brand’s own standard, not an independent one. But the underlying idea is one shared by almost all of skateboarding: an ABEC 7 or 9 won’t make you go faster at a skatepark.
How to clean Bones bearings
These are the steps the brand recommends:
- Pop off the shield with a pin or the tip of a blade, without bending it.
- Clean the bearing with a solvent: acetone, isopropyl alcohol, denatured alcohol or a citrus cleaner. Never use gasoline, kerosene, thinner or turpentine.
- Clean the rubber shield with just soap and water, never with solvent.
- Dry it well, with a lint-free cloth or compressed air.
- Lube it: two drops of Speed Cream per steel bearing, one per ceramic bearing.
- Put the shield back with the Bones name facing out.
Bones also sells the Bones Bearing Cleaning Unit, a jar with an axle in the lid: you put in all eight bearings with spacers, pour in solvent up to a third, shake for about 30 seconds and repeat. Reds come lubed from the factory, so cleaning them is maintenance, not an obligation.
When you mount the bearings in the wheel, press only on the outer race: if you push on the shield, it dents and the bearing drags. They also need about an hour of use to settle in. You have the full process in our guide to cleaning skateboard bearings.
How to avoid fake Bones
Reds are among the most counterfeited skate products. Bones doesn’t publish a guide to tell copies apart at a glance, but it does give these clues:
- Buy from official dealers. Bones has a list of authorized dealers, and only they give a warranty. On the big marketplaces many bearings are used or fake.
- Since 2018 all boxes carry a Skate Rated sticker. If it doesn’t have one, be wary.
- A price well below normal is almost always a bad sign.
- Swiss that say “Made in China” are fake. Swiss are made in Switzerland; only Reds are made in China.
Bones vs Spitfire
Bones and Spitfire are the two most used wheel brands, and their main lines, STF and Formula Four, are very similar in hardness and flatspot resistance. The differences:
- Bones organizes its wheels by formulas, one for each terrain: STF, SPF, X-Formula, ATF. That makes it easy to choose based on where you skate.
- Spitfire concentrates almost everything in the Formula Four and offers more shapes within it: Classic, Conical, Conical Full, Lock-In, Tablet…
- Both manufacture in the United States, and Bones with its own urethane and plant.
In practice, many skaters switch from one to the other without noticing much. You have the other side of the comparison in the Spitfire profile.
The Bones team
Bones has one of the biggest teams in skateboarding, between wheels and bearings. On Bones Wheels there are, among many others, Tony Hawk, Steve Caballero, Paul Rodriguez, PJ Ladd, Torey Pudwill, Chris Joslin, Felipe Gustavo, Matt Berger, Nate Greenwood, Lizzie Armanto, Rayssa Leal, Sky Brown, Bryce Wettstein, Keegan Palmer and the Frenchman Aurélien Giraud, who has his own STF wheel.
In 2015 Bones Wheels brought back the Vato Rat as its main logo, a rat with a spray can that came from the Powell Peralta graphics of the 80s. That same year it put out a pro wheel for Leticia Bufoni, one of the first signature wheels for a female skater.
Which Bones should you pick?
Wheels:
- Street: STF 99A, in V1, V2 or V5.
- Skatepark and bowl: SPF, especially if the ground is smooth.
- Rough ground: X-Formula X97 or X95.
- Cruiser or filming: ATF Rough Riders or Filmer.
Bearings:
- If you’re starting out or skate once in a while: Reds.
- If you skate a lot: Super Reds, which last longer and make less noise.
- If you want the fastest: Swiss or Swiss 6.
- If you skate in wet areas: ceramics don’t rust.
And whichever you choose, buy them from a shop you trust.
Frequently asked questions
Who owns Bones?
Skate One Corp., George Powell's company based in Goleta, next to Santa Barbara, California. It's the continuation of the company Powell founded in 1976 and it has never been sold to another group. Skate One also owns Powell Peralta and Mini Logo.
Are Bones Wheels and Bones Bearings the same brand?
They are two sister brands under the same owner, Skate One. Bones Wheels makes wheels (STF, SPF, X-Formula, ATF) and Bones Bearings makes bearings (Reds, Super Reds, Swiss). Each has its own website and catalog.
Where are Bones bearings made?
Bones Swiss are made in Switzerland, by a small custom manufacturer. Reds, Super Reds and Big Balls are made in China to Bones' specifications, and the brand says so openly. If a box of Swiss says they were made in China, it's fake.
What's the difference between Bones Reds and Swiss?
Swiss are made in Switzerland with better tolerances and materials: they're faster, last longer and cost quite a bit more. Reds copy the Swiss design, are made in China and cost less than half. For most skaters Reds are enough.
Bones Reds or Super Reds?
Super Reds have better quality steel races, more precise balls and a better finish. They're a bit quieter and last longer, but the speed difference is small. If you skate a lot, they're worth it; if you're starting out, Reds are plenty.
What ABEC rating do Bones Reds have?
None. Bones doesn't use the ABEC scale because it was made for industrial machines that spin at thousands of revolutions, not for the impacts and side loads of skateboarding. It uses its own standard, which it calls Skate Rated.
How do you clean Bones bearings?
Pop off the shield with a pin without bending it, clean the bearing with a solvent like acetone or isopropyl alcohol (never gasoline or thinner), dry it well and put in two drops of Speed Cream. The rubber shield is cleaned with just soap and water.
How can I tell if Bones Reds are fake?
The safest way is to buy them from an official dealer. Since 2018 all original boxes carry a Skate Rated sticker, and a price well below normal is a bad sign. With Swiss, if the box says China, they're fake.
Bones STF or SPF wheels?
STFs are for the street and technical street, in 99A or 103A. SPFs are harder, on the B scale, and are made for skatepark, bowl and transition. On the street, on uneven ground, SPFs can feel too hard.
Bones or Spitfire?
They are the two most used wheel brands and their main lines, Bones STF and Spitfire Formula Four, are very similar in hardness and flatspot resistance. Bones has more different formulas by terrain; Spitfire has more shapes within the Formula Four.