Griptape is the cheapest part of the skateboard and one of the ones you notice most underfoot. A good sheet well applied makes the deck feel stuck to your shoes; a worn or badly chosen one makes you hesitate on every ollie. Choosing well is simple: the grit, the sheet size and whether you want it perforated or not. Colour and graphic are a matter of taste.
This guide tells you how griptape works, what changes between one grit and another, what sheet size to ask for depending on your deck, the differences between perforated, standard and clear, what the best-known brands are like, how long it lasts and how to look after it. The step by step for applying it is already in the tutorial on how to apply grip tape to your deck, so here we focus on what to buy.
What griptape is and what it is for
Skateboard griptape is a sheet with one side covered in abrasive grains (normally silicon carbide) and the other with adhesive. It is stuck on the top face of the deck and is what stops your foot from slipping. Without it, your shoes would have nothing to hold on to for pushing, holding the board in the air or correcting your position after a jump. You have the short definition in the dictionary entry on griptape.
The sheet has three layers worth telling apart when buying:
- The grit: the crystals that bite the sole. The bigger they are, the more grip and the more shoe wear.
- The backing: the paper or base the crystals are stuck to. If it is stiffer, it takes knocks better; if it is thinner, it adapts better to the curve of the deck.
- The adhesive: the glue on the back. It decides whether the griptape lifts at the edges after two weeks or lasts months.
In a skate shop almost any branded sheet delivers on all three. The differences show in the details: a slightly more aggressive grit, a thinner backing or a stronger adhesive.
Grit: coarse versus fine griptape
Grit is identified by a number that indicates the size of the crystals: the lower the number, the coarser the griptape. The sheets sold by skate shops usually hover around grit 80, and it is the value most often repeated as standard. Within the usual range there are variations: some brands mix crystal sizes, and manufacturers do not always number the same way, so an 80 from one brand is not identical to another’s.
| Griptape | Grip | Shoe wear | Who it is for |
|---|---|---|---|
| Coarser | Very high | Fast | Technical street, flips, anyone who wants the board “stuck” |
| Standard (~80) | High and balanced | Medium | Almost everyone, to start and to keep going |
| Finer | Moderate | Slow | Bowl, ramp, cruising, anyone who looks after their shoes |
What you notice in practice:
- More grip means the foot stays more secure when doing ollies, flips or grabs, but the shoe sole wears sooner. In very intense sessions, shoe wear is the price of grip.
- Less grip looks after your shoes and is comfortable for cruising or for ramp and bowl, where the foot does not make such sudden movements. In technical tricks it can fall short.
- Too fine is a common mistake: the shoe slips just when you try a trick that takes the foot to the edge of the deck.
Sheet size: what to ask for depending on your deck
Griptape is sold in rectangular sheets larger than the deck, and trimmed when applied. The sheet has to be the same width as the deck or wider and also longer, with room to adjust the position.
| Sheet (inches) | For which decks |
|---|---|
| 9 x 33 | The standard: works for current street and park decks |
| 10 x 33 or 10 x 34 | Wide decks or old school shapes |
| 11 x 33 | Very wide and old school shapes |
| 12 x 34 | Large old school-type shapes |
Current skateboard decks measure between 7.5 and 8.5 inches wide and around 31 or 32 long. That is why the 9 x 33 sheet is the usual one: it covers any popsicle with no problem. If you want to check the width of your deck, you have the full table in the skateboard deck size chart. Sheets of 10 inches or more are only needed on special decks. There are also long rolls of griptape, meant for shops and for people who build many decks, and longer sheets for longboards.
Perforated, standard, clear and coloured
Perforated (anti-bubble)
It has hundreds of micro-holes, barely visible, that let air out while you apply it. It is the most comfortable option for the first time, because the number one cause of bubbles is trapped air. Once applied, it grips the same as a standard one. It has to be said that the quality of the perforation varies between brands, and in some it is less effective.
Standard (unperforated)
The classic. With the right technique (peel the backing slowly and press from the centre outwards) it ends up just as good. It is what experienced skaters have always used the most and it is usually a bit cheaper.
Clear
It lets you see the graphic or the colour of the wood. It grips almost the same as a black one, but since it covers nothing, any imperfection shows: old glue residue, scratches or uneven wood. That is why it is best applied on a clean, well-prepared deck. It usually costs a little more.
Coloured and with graphics
There are plain coloured sheets and others with printed designs (skulls, brand logos, full graphics). Almost all are printed on the same type of grit, but keep in mind that a large, dense print can reduce grip in that area, because the ink covers part of the crystals. If the design covers almost all of the griptape, check it is from a brand that looks after grip.
Soft or foam
There are foam or softer griptapes, meant for small kids or for anyone who does not want to wreck their footwear. They work, but the grip is clearly lower. For tricks, better a normal-grit one.
Griptape brands: traits you do notice
Almost all brands make theirs with silicon carbide and similar grit. What changes are the nuances reported by people who use them every day. This table sums up the most common ones without exaggerating:
| Brand | Usual traits | Usually liked by |
|---|---|---|
| Mob | Slightly more aggressive grit, perforated version widely available, brand graphics | Those doing technical street who want grip |
| Jessup | Slightly finer grit, strong adhesive, on the market since the seventies | Beginners or anyone who wants to look after their shoes |
| Grizzly | Middle ground between the two above, eye-catching designs | Those who skate street and park equally |
| Black Diamond | Plain coloured, printed and clear sheets, and big rolls | Those looking for variety of finishes |
| Shake Junt | Brand known for its graphics; the sheets carry the brand’s designs | Those who care about looks |
| Black Magic | Described as high grip with a thinner backing | Those who prefer a feel closer to the deck |
The grit difference between Mob and Jessup is noticed mostly at the start of the griptape’s life; in use, the grip is more alike than forums say. What is true is that sheets with a more aggressive grit wear soles out sooner.
Some deck and accessory brands also sell their own griptape. If you like a brand for the graphics on its decks, it is common for it to offer sheets with its logo, but in terms of grip they perform like the others in their range.
Which griptape to choose by profile
- Beginner. Black 9 x 33 sheet, standard grit and perforated. It is cheap, easy to apply and does not limit you. Before spending more, see whether the builder suggests something for the rest of the parts: skateboard builder.
- Technical street. Standard grit or slightly more aggressive. If you do a lot of flips, you will notice the difference. Be ready to change shoes more often.
- Park and bowl. A standard or slightly finer grit works well. On ramp you spend more time planted than making sudden foot movements.
- Getting around the city. A standard griptape is more than enough. If you use your foot a lot for pushing, better a standard grit than a very fine one.
- Kids. A standard sheet of normal size, or a softer one if the child is very small. If the deck is a small size, check that the sheet covers it well.
- Wide deck. Check the width. Up to 8.5 inches the 9 x 33 works. For bigger widths or special shapes, ask for the 10 or 11 inch one.
If you are building your first skateboard, the rest of the decisions are in the guide on how to choose a skateboard deck and the one on how to build a complete skateboard, which also has the order of applying and assembly.
How long griptape lasts and how to look after it
Lifespan. With regular use people usually talk about 3 to 6 months before the grit smooths out. If you skate little or look after it, it lasts quite a bit longer; if you skate street almost every day, it can fall short of that. There is no fixed date: replace it when your foot slips or the edges lift, not because a certain time has passed.
Signs it is time to replace it:
- The grit is smoothed out where your foot rests and it no longer grips even if you clean it.
- Holes or peeling areas appear, especially at the edges.
- The deck has changed (you are getting a new deck) and the old griptape cannot be reused.
Cleaning. The usual way is a griptape cleaner gum: a rubber block you rub over the grit that picks up dust, dirt and light grime. It works very well against what builds up between sessions.
- Run a dry brush over it to remove surface dust.
- Rub the gum with moderate pressure over the foot area until it stops lifting dirt.
- If there is dried mud, use a stiff-bristle brush with a little water and dry with a cloth, without soaking the griptape.
A pass with the gum every few sessions, and a deeper clean every few months, extends the life of the griptape. It is maintenance as simple as cleaning the bearings, and much cheaper than replacing the griptape early.
Replacing it. To remove the old one, warm it gently with a hair dryer and pull from a corner; clean the glue residue with alcohol and apply the new one on clean, dry wood. The full process, with the edge cut, is in the application tutorial. In short: peel the backing slowly, press from the centre to the edges, mark the outline with a tool and cut with the blade angled.
Selection of griptape and cleaner
Prices change throughout the year, so we do not give exact figures: a branded sheet runs around 8-15 euros, and a cleaner gum quite a bit less. These are real options and the links take you to a search with the format already set.
Griptape sheets
- Perforated Mob Grip negra perforada 9 x 33 One of the most widespread perforated sheets. Slightly more aggressive grit than others and micro-holes to apply it without bubbles.See on Amazon
- To start Jessup Griptape negra 9 x 33 Slightly finer grit, strong adhesive and a long track record in shops. Looks after your shoes a bit more.See on Amazon
- Middle ground Grizzly Griptape 9 x 33 Sits between Mob and Jessup in grip and comes in many designs, from plain to printed.See on Amazon
- Clear Mob Grip transparente 9 x 33 Lets you see the deck graphic. Best applied on clean wood because any defect shows.See on Amazon
- Clear Black Diamond Griptape transparente 9 x 33 A clear grit 80 alternative made for decks with an eye-catching graphic.See on Amazon
Affiliate links: if you buy, Fillow earns a small commission at no extra cost to you. We pick products for what they are, not for the commission.
To clean it
- Cleaner Black Diamond Dirt Remover A rubber block you rub over the grit to lift dust and dirt and bring back the original feel.See on Amazon
- Gum Goma limpiadora de lija para skate A rubber block to run over it after sessions. Any skate-brand one will do; it is cheap and lasts a long time.See on Amazon
Affiliate links: if you buy, Fillow earns a small commission at no extra cost to you. We pick products for what they are, not for the commission.
Common mistakes when choosing and looking after griptape
- Thinking the coarser the better. More grip means more shoe wear, and while you are learning you do not need it.
- Choosing a very fine one “to protect your shoes”. If your foot slips just when you need control, the shoe ends up scraping against the ground and the wear is worse.
- Buying a sheet that falls short. Check the deck width before ordering. On wide or special decks, the 9 inch one may not be enough.
- Peeling all the backing at once when applying it. It is the cause of almost all bubbles. Perforated helps, but technique still counts.
- Putting the new one over the old one. Griptape is not reusable: lift it, clean the glue and apply on clean wood.
- Trusting only the graphic. A very dense print can take away grip. Look at the grit, not just the drawing.
- Never cleaning it. Dust and dirt fill the grit and the griptape looks worn out before its time. With a gum you fix it in a minute.
- Waiting too long to replace it. Smoothed-out griptape makes your foot slip and raises the risk of a fall. If it no longer grips, replace it.
If you are putting together your first skateboard, the rest of the parts also deserve attention: wheels, trucks and deck technology.
Frequently asked questions
Which griptape should I buy if it is my first time?
A black 9 x 33 inch sheet from a skate brand, perforated if you want to avoid bubbles when applying it. A standard shop grit (around 80) grips well and does not wreck your shoes in a couple of weeks. That covers almost any current deck and you do not need more.
What sheet size do I need for my deck?
The standard 9 x 33 inch sheet works for current decks, which are around 7.5 to 8.5 inches wide and about 31 or 32 long. You only need a wider sheet, 10 or 11 inches, if your deck is an old school shape or very wide. Before buying, compare the deck width with the sheet width.
Which is better, perforated or standard griptape?
Perforated has micro-holes that let air out as you apply it, so it is much easier to avoid bubbles. For someone applying it for the first time it is the comfortable option. Standard works the same once on, and with patience and the technique of peeling the backing slowly it ends up just as clean.
Does coarse or fine griptape grip better?
Coarse (lower grit number) grips more, but wears down the sole of your shoes sooner. Fine looks after your footwear and is less noticeable under your foot, though it gives less hold on flip tricks. The usual in shops is around grit 80, and to start it is a good middle ground.
Is clear griptape worth it?
It is a matter of looks: it lets you see the deck graphic or colour. It grips practically like a black one, but any imperfection in the wood or graphic shows, and it usually costs a bit more. If you care how your deck looks, it is a good option; if not, black does the same.
How long does a skateboard's griptape last?
With regular use it usually lasts between 3 and 6 months before the grit smooths out, and quite a bit longer if you skate little or keep it clean. In intense sessions almost every day, some brands show wear sooner. You replace it when your foot slips, not by date.
How do I clean skateboard griptape?
With a griptape cleaner gum, a rubber block you rub over the grit that picks up dust and light dirt. For dried mud, a stiff-bristle brush and a little water, without soaking the griptape. A pass with the gum every few sessions is enough to make it last longer.
Can I reuse griptape or stick a new one on top of the old one?
It is not a good idea. The adhesive of the old one lifts, the new one ends up uneven and peels at the edges. The right way is to remove the old one with gentle heat (a hair dryer), clean off the glue residue with alcohol and apply the new one on clean wood.
Which griptape brand is better, Mob or Jessup?
Mob tends to have a slightly more aggressive grit and is associated with technical street, though it wears shoes out sooner. Jessup is finer and is considered a calm option to start with. Neither is bad: it depends on whether you prioritise grip or looking after your footwear.
How much does good skateboard griptape cost?
A skate-brand sheet usually runs between 8 and 15 euros, depending on size and whether it has a graphic or is clear. Coloured ones or those with special designs can cost a bit more. For less than that there are unbranded sheets of more uneven quality.
Conversation
Your name will be public. Your email stays private. Comments are reviewed before publishing.