The rule is simple: the truck has to be the same width as your deck. The tricky part is that every brand names its sizes differently: Independent uses numbers like 139 or 149, Thunder uses 147 or 148, Venture and Tensor use hanger measurements like 5.2 or 5.6, and Ace has two lines with the same numbers and different measurements.
Here you have the equivalence between brands for each deck width, the size charts for each brand with axle width in inches and millimeters, and what truck height you need for your wheels.
Skateboard trucks size chart by brand
Pick your deck width and the row with the size you need in each brand is highlighted. If you do not know how wide your deck is, it is on the sticker or the product page (the first number, for example 8.25 x 31.9); and if you do not have one yet, check the skateboard size chart first.
Your truck size by brand
Your deck width
Look for an axle of about 8.25″ (210 mm)
Ideally the axle matches the deck width, or is no more than 1/8″ (3 mm) wider or narrower. If you get "139 / 144", you are on the boundary: both work.
| Deck | Independent | Thunder | Venture | Ace AF1 | Krux | Tensor | Royal |
|---|---|---|---|---|---|---|---|
| 7.5″ 191 mm | 129 | 145 | 5.0 | 22 | 7.6 | 5.0 | 127 |
| 7.75″ 197 mm | 129 | 145 | 5.0 | 22 | 7.6 / 8 | 5.0 | 127 |
| 8.0″ 203 mm | 139 | 147 | 5.2 | 33 | 8 | 5.25 | 139 |
| 8.125″ 206 mm | 139 / 144 | 147 / 148 | 5.2 / 5.6 | 33 / 44 | 8 / 8.25 | 5.25 / 5.5 | 139 / 144 |
| 8.25″ 210 mm | 144 | 148 | 5.6 | 44 | 8.25 | 5.5 | 144 |
| 8.375″ 213 mm | 144 / 149 | 148 / 149 | 5.6 / 5.8 | 44 / 55 | 8.25 / 8.5 | 5.5 / 5.75 | 144 / 149 |
| 8.5″ 216 mm | 149 | 149 | 5.8 | 55 | 8.5 | 5.75 | 149 |
| 8.75″ 222 mm | 159 | 151 | 6.1 | 60 | 8.5 / 9 | 6 | 159 |
| 9.0″ 229 mm | 159 / 169 | 161 | none | 66 | 9 | none | none |
When a cell says “144 / 149” it means that width falls right between two sizes and both work: the narrower one turns a bit faster and the wider one gives a little more stability.
How a skateboard truck is measured
A truck has two measurements that often get mixed up:
- Axle width: from tip to tip of the bolt where the wheels go. This is the measurement that has to match your deck.
- Hanger width: the T-shaped metal piece, not counting what the axle sticks out. It is narrower, about 2.75″ (70 mm) less than the full axle.
That is why a Venture 5.0 is not 5 inches wide: its hanger is 5.0″, but the full axle is about 7.6″. And that is why an Independent 139 is not 139 millimeters: it is a brand code that corresponds to an 8.0″ (203 mm) axle.
How much difference is allowed? Ideally the truck and deck are the same width or at most 1/8″ apart (about 3 mm). Up to 1/4″ (6 mm) is tolerated, but it starts to show: if the truck is wider, the wheels stick out and you trip over them; if it is narrower, the board wobbles and you lose stability.
Independent truck sizes
Independent publishes its own size chart, with the axle width and recommended deck for each number:
| Size | Axle width | In mm | Recommended deck |
|---|---|---|---|
| 109 | 6.9″ | 175 mm | 6.25″ to 7.6″ |
| 129 | 7.6″ | 194 mm | 7.4″ to 7.8″ |
| 136 / 139 | 8.0″ | 203 mm | 7.8″ to 8.2″ |
| 144 | 8.25″ | 209 mm | 8.2″ to 8.375″ |
| 146 | 8.375″ | 213 mm | 8.125″ to 8.625″ |
| 149 | 8.5″ | 216 mm | 8.375″ to 8.6″ |
| 151 | 8.625″ | 219 mm | 8.375″ to 8.875″ |
| 159 | 8.75″ | 222 mm | 8.6″ to 9.0″ |
| 166 | 9.0″ | 229 mm | 8.5″ to 9.5″ |
| 169 | 9.125″ | 232 mm | 9.0″ to 9.5″ |
| 215 | 10.0″ | 254 mm | 9.5″ to 10.5″ |
Sizes 136, 146, 151 and 166 are from the Stage 4 line, the classic geometry. The rest are Stage 11, the current one. In height, the standard Stage 11 and the Hollow are 55 mm, the Forged Hollow 53.5 mm, the Mid 52 mm and the Mid Forged Hollow 50.5 mm.
If you want to know which version of Independent to buy (standard, Hollow, Forged, Titanium), it is covered model by model in the Independent trucks guide.
Thunder truck sizes
Thunder uses three-digit numbers that are not real measurements. Its trucks are lower than a standard Independent (49 to 53 mm depending on the model):
| Size | Axle width | In mm | Recommended deck |
|---|---|---|---|
| 143 | 7.125″ | 181 mm | up to 7.375″ |
| 145 | 7.6″ | 194 mm | 7.4″ to 7.9″ |
| 147 | 8.0″ | 203 mm | 7.875″ to 8.125″ |
| 148 | 8.25″ | 209 mm | 8.125″ to 8.375″ |
| 149 | 8.5″ | 216 mm | 8.375″ to 8.625″ |
| 151 | 8.75″ | 222 mm | 8.625″ to 8.875″ |
| 161 | 9.125″ | 232 mm | 9.0″ to 9.5″ |
Watch out for the 149: in Thunder and in Independent it is the same width (8.5″), but the Thunder 147 equals the Independent 139 and the 148 equals the 144. The numbers look alike and the sizes do not match.
Venture truck sizes
Venture names its sizes after the hanger width in inches. It has a Low version (about 48 mm tall) in the small sizes and High (53.5 mm) in all of them:
| Size | Axle width | In mm | Recommended deck |
|---|---|---|---|
| 5.0 | 7.6″ | 194 mm | 7.5″ to 7.75″ |
| 5.2 (5.25) | 8.0″ | 203 mm | 7.875″ to 8.125″ |
| 5.6 | 8.25″ | 209 mm | 8.125″ to 8.375″ |
| 5.8 | 8.5″ | 216 mm | 8.375″ to 8.625″ |
| 6.1 | 8.75″ | 221 mm | 8.625″ to 8.875″ |
Ace truck sizes (Classic and AF1)
Ace is the brand that confuses people most: it has two lines, the Classic and the AF1, which use the same numbers with different measurements. Before buying, check which line it is.
| Size | Classic axle | Deck (Classic) | AF1 axle | Deck (AF1) |
|---|---|---|---|---|
| 22 | 7.6″ (193 mm) | 7.375″ to 7.875″ | 7.75″ (197 mm) | 7.625″ to 7.875″ |
| 33 | 8.0″ (203 mm) | 7.875″ to 8.125″ | 8.0″ (203 mm) | 7.875″ to 8.125″ |
| 44 | 8.35″ (212 mm) | 8.25″ to 8.5″ | 8.25″ (209 mm) | 8.125″ to 8.375″ |
| 55 | 9.0″ (229 mm) | 8.875″ to 9.125″ | 8.5″ (216 mm) | 8.375″ to 8.625″ |
| 60 | not available | 8.75″ (222 mm) | 8.625″ to 8.875″ | |
| 66 | 9.35″ (237 mm) | 9.25″ to 9.5″ | 9.0″ (229 mm) | 8.875″ to 9.125″ |
The typical mistake: someone with an 8.5″ deck buys an Ace 55 thinking it is their size and gets a Classic with a 9.0″ axle, half an inch wider than the deck. With the AF1 line, the 55 is for 8.5″. Ace trucks are about 52 mm tall; the AF1 also has a Low version of about 49 mm.
Krux, Tensor and Royal truck sizes
Krux uses the axle width directly as its size name, so it is the easiest:
| Size | Axle width | Recommended deck |
|---|---|---|
| 7.6 | 7.6″ (193 mm) | 7.25″ to 7.75″ |
| 8 | 8.0″ (203 mm) | 7.75″ to 8.25″ |
| 8.25 | 8.25″ (210 mm) | 8.0″ to 8.25″ |
| 8.5 | 8.5″ (216 mm) | 8.25″ to 9.0″ |
| 9 | 9.0″ (229 mm) | 8.5″ to 10.5″ |
Tensor names by hanger and comes in three heights: Low (46 mm, among the lowest trucks there are), Regular (51.5 to 53 mm) and All Terrain (55 mm):
| Size | Axle width | Recommended deck |
|---|---|---|
| 5.0 | 7.625″ (194 mm) | 7.5″ to 7.75″ |
| 5.25 | 8.0″ (203 mm) | 7.875″ to 8.125″ |
| 5.5 | 8.25″ (209 mm) | 8.125″ to 8.375″ |
| 5.75 | 8.375″ to 8.5″ (213 mm) | 8.25″ to 8.5″ |
Royal copies Independent’s numbering system and the measurements almost match:
| Size | Axle width | Recommended deck |
|---|---|---|
| 127 | 7.5″ | 7.375″ to 7.625″ |
| 139 | 8.0″ | 7.75″ to 8.125″ |
| 144 | 8.25″ | 8.125″ to 8.375″ |
| 149 | 8.5″ | 8.375″ to 8.625″ |
| 159 | 8.75″ | 8.625″ to 8.875″ |
Truck height: low, mid or high
Besides width, trucks have a height: the distance between the base and the center of the axle. It affects the wheel size you can run without it rubbing the deck when you turn (the famous wheelbite).
| Height | In mm | Wheels without risers | What for |
|---|---|---|---|
| Low | 46 to 49 mm | up to 51-52 mm | Technical street, flips, a feeling of being close to the ground |
| Mid | 50 to 53 mm | 52 to 56 mm | The most versatile: street and park |
| High | 53.5 to 58 mm | 56 mm or more | Transition, bowl, big wheels, more turn |
These figures assume normally tightened trucks. If you run your trucks very loose to turn more, the risk of wheelbite goes up and you may need a thin riser. There is no industry standard for these three categories: every brand puts the cutoff where it wants, which is why it is worth checking the height in millimeters.
If your wheels are too big for your truck, the fix is a riser between the truck and the deck, with longer bolts. You have the riser and bolt chart, and a wheelbite checker, in the skateboard wheel size and hardness chart.
Skateboard truck sizes in centimeters
If you prefer to work in millimeters, these are the real axle measurements that repeat across all brands, each with the deck it goes with:
| Axle width | In inches | For decks of |
|---|---|---|
| 19.4 cm (194 mm) | 7.6″ | 7.5″ to 7.75″ (19 to 19.7 cm) |
| 20.3 cm (203 mm) | 8.0″ | 7.875″ to 8.125″ (20 to 20.6 cm) |
| 20.9 cm (209 mm) | 8.25″ | 8.125″ to 8.375″ (20.6 to 21.3 cm) |
| 21.6 cm (216 mm) | 8.5″ | 8.375″ to 8.625″ (21.3 to 21.9 cm) |
| 22.2 cm (222 mm) | 8.75″ | 8.625″ to 8.875″ (21.9 to 22.5 cm) |
| 23.2 cm (232 mm) | 9.125″ | 9.0″ to 9.5″ (22.9 to 24.1 cm) |
If your deck comes in millimeters (some European brands do this), look for a truck with the same number of millimeters or within 3 mm.
In short
- Measure your deck (or read the sticker) and find a truck with that same “axle” width.
- 8.0″ → Independent 139, Thunder 147, Venture 5.2. 8.25″ → Independent 144, Thunder 148, Venture 5.6. 8.5″ → Independent 149, Thunder 149, Venture 5.8.
- With Ace, check whether it is Classic or AF1 before trusting the number.
- Height depends on your wheels: low up to 52 mm, mid up to 56 mm, high above that.
To choose brand, model and bushing hardness you have the guide on how to choose trucks, and if you want it all calculated at once, the calculators.
Frequently asked questions
What size trucks do I need for an 8.25 deck?
A truck with an axle around 8.25″ wide: Independent 144, Thunder 148, Venture 5.6, Ace AF1 44, Krux 8.25, Tensor 5.5 or Royal 144. Ideally the truck matches the deck or is within 1/8″ (3 mm) either way.
What does the 139 or 149 on Independent trucks mean?
It is a size code from the brand, not a measurement in millimeters. The 139 has an 8.0″ axle (203 mm) and goes with decks from 7.8″ to 8.2″; the 149 has an 8.5″ axle (216 mm) and goes with decks from 8.375″ to 8.6″.
What trucks go with an 8.0 deck?
Independent 139, Thunder 147, Venture 5.2, Ace 33, Krux 8, Tensor 5.25 or Royal 139. They all have an axle of about 8.0″ (203 mm).
Can I use trucks wider or narrower than the deck?
A little, yes: up to 1/8″ (about 3 mm) you will not notice it and up to 1/4″ (6 mm) it is tolerated. Beyond that, if the truck is wider the wheels stick out and you trip over them; if it is narrower, the board gets unstable and turns strangely.
What is the hanger of a truck?
It is the T-shaped metal piece that the axle goes through (the bolt where the wheels sit). Some brands, like Venture or Tensor, name their sizes after the hanger width in inches (5.0, 5.25, 5.6...). The total axle width is about 2.75″ (70 mm) more than the hanger.
Low, mid or high trucks?
Low (46-49 mm tall) for small wheels up to 51-52 mm and technical street; mid (50-53 mm) for wheels from 52 to 56 mm, the most versatile; high (53.5-58 mm) for wheels of 56 mm or more, transition and anyone who wants more turn.
Is an Ace 55 the same as an Ace 44?
No, and it also depends on the line. The Ace 55 Classic has a 9.0″ axle and the Ace 55 AF1 an 8.5″. The 44 Classic is 8.35″ and the 44 AF1 is 8.25″. With Ace always check whether it is Classic or AF1.
How wide are skateboard trucks in centimeters?
The most common ones have an axle between 19.4 and 22.2 cm wide: 194 mm (7.6″), 203 mm (8.0″), 209 mm (8.25″), 216 mm (8.5″) and 222 mm (8.75″).
Conversation
Your name will be public. Your email stays private. Comments are reviewed before publishing.