GUÍAS

Skateboard Wheel Size and Hardness Chart: Durometer, Diameter and Risers (2026)

Skateboard wheel size chart: what diameter and durometer to pick for where you skate, how to read the A and B scales, each brand's formulas and when you need risers and longer bolts.

A skateboard wheel is defined by two numbers: the diameter in millimeters and the hardness on the A scale. For street and skatepark the most common choice is a wheel of 52 to 54 mm and 99A. For transition you go up in size, and for riding around the city you drop the hardness a lot.

Here you have the diameter and durometer charts, how to read the A and B scales, what each brand offers, and a tool to find out whether your wheels and trucks need risers and which bolts to buy.

Skateboard wheel diameter chart

Diameter is how wide the wheel is from side to side. Small wheels weigh less and accelerate sooner; big ones hold speed better and roll over rough ground more easily.

DiameterWhat forHow they feel
49 to 52 mmTechnical streetLight, quick flips, low trucks
52 to 54 mmStreet and skateparkThe most versatile size
54 to 56 mmPark, small bowl, minirampMore sustained speed
56 to 60 mmBowl, vert, poolsLots of momentum on the walls
56 to 60 mm or more (soft)Cruising, getting around town, filmingRoll over cracks and pebbles

The wheel size you can fit also depends on your truck height: with low trucks you should not go past 52 mm without a riser. More on that below.

Skateboard wheel hardness chart

Hardness is measured with a durometer on the A scale. The higher the number, the harder the wheel.

HardnessTypeWhat for
78A to 87AVery softCruising, bad asphalt, filming. Grips a lot and is no good for slides
88A to 95AMediumRough street with some tricks, transition with grip
96A to 99AHardSkatepark, street on good ground. 99A is the standard
100A to 104AVery hardTechnical street and smooth park. Slides a lot, vibrates on rough ground

Hard wheels slide better (for powerslides and reverts) and last longer; soft ones grip more and are more comfortable, but they bounce when you land tricks and wear out sooner.

A scale and B scale: how they compare

The A scale stops being precise around 100A, so some brands (mostly Bones) use the B scale for their hardest wheels. The equivalence used is to add 20 points to go from B to A:

B scaleEquivalent (approx.)
80B100A
81B101A
83B103A
84B104A

It is an approximate equivalence: the two scales measure differently and some independent tests give slightly different figures. It works for comparing, not as an exact measurement.

In some shops you will see Spitfire wheels marked as “99D” or “101D”. The same wheels appear elsewhere as 99A or 101A: take it as the same hardness on the A scale.

Wheel diameter and hardness combinations by style

StyleDiameterHardness
Technical street (flips, ledges)50 to 53 mm99A to 101A
Street and skatepark52 to 54 mm99A
Park, bowl, miniramp54 to 58 mm97A to 101A
Vert and pools56 to 60 mm97A to 99A
Rough street with tricks54 to 56 mm90A to 95A
Cruising and getting around56 to 60 mm78A to 87A

If you want it calculated by crossing your style, the ground and your weight, you have the calculators.

Formulas and shapes from the best-known brands

The big brands have their own urethane formulas and several wheel shapes. The shape changes the contact patch (what touches the ground) and how the wheel fits on grinds.

Spitfire Formula Four. Sold in 93, 97, 99 and 101. It has many shapes: Classic and OG Classic (rounded), Conical and Conical Full (wider, more grip and stability), Radial (round edge), Tablet (straight cut, narrow footprint) and Lock-in (asymmetric, designed to lock onto round rails).

Bones. The STF (Street Tech Formula) is made for street and is known for holding up to slides without flat spotting; it is sold in 99A and 103A (83B), in shapes V1 to V6. The SPF (Skatepark Formula) is for park and transition, in 81B and 84B.

OJ Wheels. The Elite Hardline (99A and 101A) are their street wheel; the Nomads (95A) are a middle ground, and the Super Juice (78A) are soft for cruising.

Ricta. The Clouds are soft (78A to 92A, 52 to 60 mm) and are widely used for riding on the street and for starting out on bad ground. The Sparx are their hard street wheel (99A).

Powell Peralta Dragon Formula. A slightly softer formula (93A and 97A) with good grip, in very varied shapes from narrow to wide patch.

All the good brands work. The difference between formulas shows up in how long they last, how easily they flat spot from slides and in grip, more than in speed. It is compared in the guide on how to choose wheels.

Risers and wheelbite

Wheelbite is when the wheel touches the deck while turning. It stops you dead and usually ends in a fall. It happens when the wheel is too big for the truck height. It is fixed with a riser: a plastic plate between the truck and the deck, normally 1/8″ (3 mm), 1/4″ (6 mm) or 1/2″ (13 mm).

Enter your wheel diameter and your truck height:

Do you need risers?

Your truck height
RiserNot needed
Bolts7/8″

Assumes normally tightened trucks. If you ride them very loose, go one riser step up. Thicker decks (8 or 9 plies) need 1/8″ longer bolts.

Wheel diameterRiser with mid trucksRiser with high trucks
49 to 54 mmNot neededNot needed
55 to 56 mmOnly if your trucks are loose (1/8″)Not needed
57 to 58 mm1/8″Optional, 1/8″ if loose
59 to 60 mm1/8″ to 1/4″1/8″
61 to 64 mm1/4″1/8″ to 1/4″
65 to 67 mmBetter to get higher trucks1/4″ to 1/2″

With low trucks (46 to 49 mm) the margin is smaller: up to 52 mm without a riser and from there it is better to move up to a taller truck or use smaller wheels. Squashed bushings or ones too soft for your weight, and very loose trucks, also cause wheelbite.

A thin riser (1/8″) is barely noticeable. One of 1/4″ or more raises your center of gravity and costs a bit of stability: if you can, go for smaller wheels or taller trucks instead.

What bolt length you need

Skateboard bolts (the hardware) are sold by length in inches. If you add risers, you need longer bolts:

RiserBolt length
No riser7/8″ (or 1″ with thick decks)
1/8″1″ to 1 1/8″
1/4″1 1/4″
1/2″1 1/2″

7-ply decks, the normal ones, take 7/8″ without a riser. Some thicker decks (8 or 9 ply) need 1/8″ more. If the bolt sticks out a lot past the nut, it is too long; if it does not poke through, it is too short and the nut does not grip.

Skateboard bearing size

There is nothing to choose here: all skateboard bearings are 608, meaning an 8 mm inner bore (what the axle measures), 22 mm outer diameter and 7 mm wide. Each wheel takes two, with a spacer between them that keeps them aligned.

What does change between bearings is manufacturing quality, the ball material (steel or ceramic) and whether they come with a built-in spacer. It is covered in the Bones bearings guide.

In short

  • Street and skatepark: 52-54 mm, 99A.
  • Bowl and transition: 54-58 mm, 97A-101A, with high trucks.
  • Street riding and cruising: 56-60 mm, 78A-87A.
  • B scale: add about 20 to compare it with the A scale (83B ≈ 103A).
  • More than 56 mm with mid trucks: you probably need a 1/8″ riser and 1″ bolts.

For the rest of your setup, check the truck size chart and the skateboard size chart.

Frequently asked questions

What is the most common skateboard wheel size?

For street and skatepark, between 52 and 54 mm with a 99A hardness. It is the best-selling combination and the one that works for almost everything: flips, ledges and a bit of park.

What wheel hardness is best for beginners?

If you are going to learn tricks at a skatepark or on smooth ground, 99A. If you will mostly skate on the street on rough asphalt, something softer (90A to 95A) is welcome. Very soft ones (78A-87A) are for getting around, not for tricks.

What does 99A mean on a skateboard wheel?

It is the hardness measured on the A scale of the durometer. The higher the number, the harder the wheel: 78A is very soft and grips a lot, 99A is hard and slides well, 101A is even harder and fast on smooth ground.

What is the B scale on Bones wheels?

It is another hardness scale that starts where the A scale stops being precise. To go from B to A you add about 20 points: 83B is roughly 103A and 84B is 104A. It is an approximate equivalence, not an exact one.

What wheels are good for riding on the street?

Soft and slightly bigger wheels: 56 to 60 mm and 78A to 87A. They absorb cracks and pebbles and make less noise. To mix street riding and tricks, a 54-56 mm at 90A-95A is a good middle ground.

When do I need risers?

When the wheel is too big for the truck height and rubs the deck when turning (wheelbite). With mid trucks, from about 57 mm you usually need a 1/8″ riser; with low trucks, from 53 mm.

What bolt length do I need?

Without a riser, 7/8″ (or 1″ with thicker decks). With a 1/8″ riser, 1″ to 1 1/8″. With 1/4″, 1 1/4″. With 1/2″, 1 1/2″.

What size are skateboard bearings?

All skateboard bearings are 608: 8 mm bore (what the axle measures), 22 mm outer diameter and 7 mm wide. That is why any skateboard bearing fits any skateboard wheel.

Publicidad

Conversation

Your name will be public. Your email stays private. Comments are reviewed before publishing.

Loading comments...
Expert content
Every guide is reviewed by our editorial team with 20+ years in skateboarding.
Always up to date
We refresh recommendations every season with the gear that actually works.
Skate at heart
We test everything we recommend. If we wouldn't ride it, it's not in here.